Your cart is empty.
Your cart is empty.
North- Boat Wedge transom saver, works with all three ram Yamaha outboard motors.
The package also include the centering clips to keep your outboard straight when towing.
It sames to M-Y Wedge transom saver
Fits :
1、Yamaha outboards (Including SHO) outboards 115 HP to 350 HP（2 / 3-Ram Trim / Tilt Systems）
2、Mercury outboards 135 HP to 300 HP （2 / 3-Ram Trim / Tilt Systems）
3、Honda outboards 90 HP to 300 HP （2 / 3-Ram Trim / Tilt Systems）
4、Johnson outboards 150 HP - 300 HP （2 / 3-Ram Trim / Tilt Systems）Works on these models: Carb. EFI, Opti-Max, SHO,2-Stroke, 4-Stroke, Hpdi, ETEC, Ficht and Offshore, with 3 RAM SystemsJohnson 4-Stroke outboards 150 HP - 300 HP with 3-Ram Trim / Tilt Systems
5、Suzuki four stroke outboards DF140 HP - DF300 HP （2 / 3-Ram Trim / Tilt Systems）
Installation Notes:
Install on Trim / Tilt Switch Side (Normally Starboard Side of Mercury / Honda / Johnson 4-Stroke, Johnson Outboards)
Install on Trim / Tilt Switch Side (Normally Port Side of Yamaha / Suzuki Outboards
F300-F350 V-8 models need 2 m- units, port and starboard)
1. Trim outboard to up position
2. Simply slideNorth-Boat Wedge on Trim / Tilt switch side normally Port side (see note) of Yamaha / Suzuki and normally Starboard side of Mercury / Honda / Johnson over Trim/Tilt piston rod of Lower unit
Note: (On Yamaha/Suzuki the trim/tilt switch may be on the Starboard side, if there is a grease zerk where the m- meets the swivel bracket, the m- must go on the Port or Starboard side depending on where the grease zerk is)
3. North-Boat Wedge will position and self-center, slide completely down.
4. Trim outboard down until the rubber begins to compress
5. To remove North-Boat Wedge simply trim outboard to up position and remove
6. Store North-Boat Wedge in any boat compartment for convenience
Note: Manufacturer recommends that you No
W Werthy Reviews
July 29, 2025
I have used this extensively for my Suzuki df150. The only word of advice that I would offer is to use it on whatever side does not have the grease fitting on the motor.
K F
July 24, 2025
Works perfect on my Yamaha 250 vmax. I trailer most everywhere and like the stability this brings. a lot cheaper than a dealer.
Luis223
July 10, 2025
I’m recommend 💯 this product hold my Yamaha 150 real good
Brian Barton
June 4, 2025
This idea of a Transom saver was a great. Seems to work great along with the steering cylinder blocks. I liked the idea of taking the stress off the transom hydraulic system.
Steve H.
May 29, 2025
This is great, the way to go, strong and secure
Jeffrey R. Minchew
May 28, 2025
Doesn’t fit my new Suzuki 150 outboard. Way too large.
Placeholder
May 6, 2025
Super lightweight but unfortunately I felt like it was too short for my application on my engine.
Nickola Blace
February 24, 2025
cannot figure out how to use this on my motorcycle, the instruction is unclear, the product’s quality is questionable.
Chris Fratoni Cathy Fratoni
January 28, 2025
The product is well made and fits my Yamaha 1995 115 HP 2 stroke outboard motor 3 ram system .I am very pleased with the construction of this product. It is the same as the My Wedge transom saver .
MJB
December 20, 2024
I used 2 of the round supports with the white plastic sleeves. Rubber is too soft and would bend at end too much. Both plastic tubes split wide open end to end. This product is only for small outboards at best. I have reordered a different brand that has the correct design for my outboards. Use a brand that specifically lists your type and HP of outboard.
Recommended Products
